Phone:0086-371-55629010
PolyPro is a polypropylene vent pipe for use with ANSI Category II and IV gas-burning appliances, including highefficiency water heaters, condensing boilers and warm air furnaces. Poly Pro is listed by Intertek to the ULC S636 standard in Canada as a Class IIA, IIB and IIC vent system suitable for exhaust temperatures up to 230°F / 110°C, and
Learn MoreThen please ensure he is aware that latent heat recovery in the boiler exhaust comes from the conversion of steam to condensate, not from the further cooling of condensate. During the transfer from (invisible) steam to (visible) vapour the temperature remains constant. The cooling of water vapour to extract heat requires a change in temperature.
Learn MoreCall today to learn more about Clayton Exhaust Gas Boilers and industrial boilers heat recovery steam generators. Clayton Waste Heat Boilers Built from the coil sections of Clayton's fired steam generators, these units are used for higher exhaust gas inlet temperatures up to 3,000°F, and are capable of handling exhaust gas flows in the
Learn MoreA temperature sensor or probe with a high-limit control could be inserted into the flue at the flue connection to the boiler or water heater. This control would shut off the burner if the flue gas temperature exceeds the temperature rating of the flue pipe.
Learn MoreAppliance type Exhaust Temperature (o F)(o C)Chemical Oxidation: 1350 - 1475: 730 - 800: Annealing furnace: 1100 - 1200: 590 - 650: Fluidized-bed combustion: 1600 - 1800
Learn MoreSince the final exhaust from a condensing boiler has a lower temperature than the exhaust from an atmospheric boiler 38°C (100°F) vs. 204°C (400°F) a mechanical fan is always required to expel it, with the additional benefit of allowing the use of low-temperature exhaust piping (typically PVC in domestic applications) without insulation or
Learn MoreIf the exhaust temperature of steam is high so there could be several problems 1. If it is a condensing type of turbine then because of high temperature steam will not condense properly and it would be a liquid vapour phase at the inlet of condens
Learn MoreA sufficiently high boiler water temperature allows the exhaust gas temperature to be maintained well above the dew point and reduces the chance of sulphurous acid condensing out of the flue gas and falling back into the boiler where it will cause damage. Exhaust gas that falls below the dew point will produce condensation.
Learn MoreThe exhaust gases leaving the boiler are generally at high temperature and this waste heat is extracted by installing an Economiser or Water Preheaters to preheat the feed water to the boiler and Air Preheaters to pre-heat the air coming from the Forced Draft Fan required for the combustion of fuel.
Learn More9. Multiple boilers and storage tanks shall be installed with reverse return piping (as shown). 10. Mixing valves are recommended on all tanks if hot water temperature is above 119oF. 11. Expansion tank must be rated for use with potable water. 12. Use either indirect/tank sensor or system/pipe sensor mounted on common return to the boiler. 13.
Learn Morecontrol that modulates the boiler's output target temperature relative to the actual heating loads. When using this type of control, the boiler's supply temperature decreases as the outdoor temperature rises, thus ensuring lower return water temperatures. The desired outcome is the matching of space heating needs with the heat delivered.
Learn MoreThe exhaust emissions from the CO boiler must be controlled reliably and predictably to meet operating company requirements. Principal constituents for control in the exhaust emissions include carbon monoxide (CO), oxides of nitrogen (NOx), sulphur oxides (SOx) and particulate matter.
Learn MoreHot water boiler exhaust flue gas temperature directly determines the boiler efficiency, higher exhaust flue gas temperature will lead to the increase in heat loss. Heat loss caused by exhaust flue gas is the greatest part of heat losses that affect boiler efficiency, about 5 ~ 10%.
Learn MoreIn emergency mode the exhaust gas boiler can therefore be operated with low water level and even without water with the full exhaust gas flow through the boiler tubes, provided the boiler is operated depressurised and the inside temperature does not exceed 400˚C. For inside inspection, the boiler is arranged with both hand holes and manholes.
Learn MoreThe boiler is the part of the system that heats the water to be distributed. The key elements of a boiler include the burner, combustion chamber, heat exchanger, exhaust stack, and controls. Boiler accessories including the flue gas economizer are also commonly used as an effective method to recover heat from a boiler. Key Components of Boilers
Learn More